Earthworks
Earthworks

M30

Earthworks M30 on RigShare
The Earthworks M30 is a precision engineered 30 kHz omnidirectional measurement microphone ideally suited for acoustical measurements including loudspeaker design and quality control, sound system setup and troubleshooting, room acoustics, or any application where an accurate free-field measurement microphone is required. Performance Accuracy, consistency, and reliability have made the Earthworks M30 measurement microphone the first choice of live sound professionals, acousticians, and researchers all over the world for nearly twenty years. Used on countless full-scale concert tours, as well as in scientific research laboratories, tropical rainforests, and rocket testing facilities, the M30 and its M-Series siblings have proven to be lab-grade audio instruments that can handle any environment. The M30's audio performance is unparalleled. It has a flat frequency response that extends from 3 Hz to 30 kHz, an exceptionally consistent omnidirectional polar response, 140 dB SPL rating without distortion and no handling noise. With temperature compensated electronics, the M30 was built to deliver repeatable results no matter what the environment. Extremely fast impulse response and linear phase response make the M30 ideal for use with high-quality FFT-based real-time audio system measurement software like SMAART, SIM, REW, Electroacoustics Toolbox, FuzzMeasure and others, as well as for use in PA system alignment and loudspeaker design. Every M30 is individually hand-tuned and tested and is delivered with its own printed frequency response chart. An Electronic Calibration File (ECF) is generated for each microphone during final testing, and can be downloaded free of charge after product registration. Features: 30 kHz flat frequency response Ideally suited for acoustical measurements including loudspeaker design and quality control, sound system setup and troubleshooting, room acoustics, or any application where an accurate free-field measurement microphone is required Improved version of the SMAARTMIC previously offered by EAW Omnidirectional polar pattern Flat frequency response, fast impulse response and exceptional polar characteristics Used by SMAART, MLSSA, Spectrafoo, TEF and RTA in addition to acoustic measurement systems manufactured by dbx, DEQX and others Meets or exceeds ANSI Type 1 and applicable IEC 61094 requirements Each M Series microphone is delivered with its own calibration chart providing its individually measured open-circuit sensitivity and the frequency response curve Electronic Calibration File available Operating Temp Range: -20 deg C to +60 deg C ( -4 deg. F to 140 deg. F) Storage Temp Range: -40 deg C to +80 deg C ( -40 deg. F to 176 deg. F) Humidity: Up to 90% Re-calibration recommended every five (5) years

What Musicians are Saying

One-liners are short gear reviews by the RigShare community.

Let us know what you think!

Write the first one-liner about the Earthworks M30

sponsored
Buy and Sell at Reverb

Similar Gear

Zvex Pedals TB-1 Tea Ball Microphone on RigShare
Zvex Pedals
Zvex Pedals

TB-1 Tea Ball Microphone

Introducing the model TB-1 Tea Ball Microphone by ZVEX Effects, designed for specialty use on stage and in the studio. The special circuitry of the TB-1 causes it to reject sound from sources that are further than an inch or so away from the grille. This allows the mic to be placed on stage in a loud environment and plugged directly into a guitar amp that's turned up to a level that would cause any normal microphone to squeal furiously. In the studio when recording a guide vocal track in a live recording room, the TB-1 will reject the amplifiers and drums. This way the guide vocal can be used for rough mixes without fear of hearing other instruments or room ambience loudly in the background. Why is it called the Tea Ball Microphone? It's actually built inside a stainless steel tea ball, the kind of device used to make a hot mug of goodness from a tin of loose tea. The clip that holds the tea ball shut is used to open it up to change two CR2032 batteries. These have a life of about 100 hours and presently cost less than $10 for 20 units on Amazon (Sony CR2032). The mesh on the tea ball will never chip your teeth like an SM58 because it's quite springy. That's important because the best sound from this mic comes from putting your mouth right up against it. The entire mic disassembles easily by unplugging the electronics and lifting out the internal foam windscreen which can be washed in soapy water. Be sure to dry it before reassembling. The mesh ball is suspended inside a thick copper hoop using three springs for a look like something from the early part of last century. The TB-1's output level is similar to that of a guitar. It has a 1/4" female jack that runs smoothly parallel to the microphone stand. The mic is powered up by being plugged in and turned on with a switch on the back. When the mic is unplugged, the battery will not drain no matter which position the power switch is in. When the mic is live, an LED gently glows near the switch, visible from FOH so that the sound engineer can be sure it's working. Enjoy!

Audix Microphones SCX1 Drum Microphone on RigShare
Audix Microphones
Audix Microphones

SCX1 Drum Microphone

The SCX1 is a professional studio cardioid condenser microphone designed for a wide variety of recording, broadcast and live sound applications. Known for its high sensitivity, pin-point accuracy, low profile and consistency, the SCX1 is also available with hypercardioid (model SCX1HC) or omni-directional (model SCX1O) capsules.With a smooth uniform frequency response from 40 Hz - 20 kHz, the SCX1 is very consistent when responding to on and off-axis signals, and exhibits excellent phase coherence and minimal proximity effect. The SCX1 is characterized with a wide cardioid polar pattern; this, coupled with the high output and sensitivity of the microphone, makes the SCX1 an ideal choice for miking overhead, drums, instruments, room ambience, orchestral sections, stringed instruments, piano, vibes and sound effects. The SCX1HC condenser microphone is a number one choice for miking hi-hat both live and in the studio.Other features include a 21 mm gold vapor capsule, miniaturized electronics and an extremely small footprint. The SCX1 will handle sound pressure levels of 130 dB and will provide up to 20 dB of ambient noise rejection. In addition to acoustic instruments, the SCX1 is an excellent choice for group vocals, speech or Foley work. The SCX1HC has become a popular choice for interior dialogue boom pole miking. It has a precision machined brass body, interchangeable capsules, black multi-layer class ‘A' liquid finish and gold plated XLR connector. The SCX1 studio condenser microphone is manufactured to exacting standards and tight tolerances.